 |
home | products | applications | faq | blog | about |
Plasma Distribution
In order to retrofit engines with high energy plasma ignition systems, the high voltage signal from the coil / distributor has to be 'mixed' with the high current signal from the plasma module and the combined energy then delivered to the spark plug. This 'mixing' should ideally be done as close to the spark plug as possible with the high current signal traveling as short a distance as possible from the plasma module through zero resistance wires. The SparkAmp Ignition Module is equipped with a fault indicator LED, which can be used to determine if a single channel or ignition cable is faulty.
Stage I kits include RF suppression plasma cables with various boot configurations to fit a wide variety of vehicles. This setup minimizes EMI / RF intereference which may otherwise disrupt sensitive electronics and sensors, such as EFIEs which are popular with hypermilers and fuel efficiency technicians to boost up their fuel economy when coupled with plasma ignition systems.
Stage II kits include the plasma distribution bricks which provide 60kV of built in protection. This is the recommended setup for race engines which run a combination of high compression and/or high boost. This is also recommended for engines that run extremely hot which may require heavier duty ignition cables. Copper core, zero resistance cables MUST be used for the output connections going from the plasma distribution brick to the spark plugs.
Plasma Ignition Cables (Stage I)
(Hover over image for additional details:)The Molded RF Suppression Plasma cables are the latest in plasma automotive technology. Their design is optimal for easy installation and the design is the best solution to excessive RF and EMI noise that is rampant when zero resistance copper core ignition cables are used. The cable consists of two separate conductors, one carrying the high voltage energy from the distributor / coil, and the other carrying the high current plasma from the SparkAmp module. Both these conductors meet at the spark plug boot end where there is adequate high voltage (40 kV) and low voltage (5kV) protection so that upstream electronics are amply protected.
Radiant Plasma Spark Generator Specification
- Dual Conductor Hi-temp silicone
- High voltage conductor has built in RF suppression
- High voltage conductor is 8mm spark plug wire
- Plasma current delivery with 14 Gauge Stranded
- Internal Protection of 40kV
- Comes with Heat Shield and RF grounding jacket (can be removed for optimal fitment)
- Straight boot length (without metal jacket): 3.75in
| Singles | 4-Cable Set | 6-Cable Set | 8-Cable Set |
|
$39.99
|
$129.99
|
$179.99
|
$219.99
|
Long Boot Plasma Ignition Cables (Stage I)
These plasma cables are suited for engines where the spark plugs are recessed. Instead of having a second conductor coming out of the boot, a threaded nut is exposed on the top of the boot which is used to connect the output from the plasma module.
Long Boot Plasma cable
- Long reach boot for engines with recessed plugs
- High voltage wire from boot is 3ft in length
- High voltage conductor is 8mm spark plug wire
- Plasma current delivery through screw connect
- Bolt on flange for secure installation
- Internal Protection of 40kV
- Boot length: 6"
- Boot Diameter (widest point): 15/16"
- Long reach boot for engines with recessed plugs
- High voltage wire from boot is 3ft in length
- High voltage conductor is 8mm spark plug wire
- Plasma current delivery through screw connect
- Bolt on flange for secure installation
- Internal Protection of 40kV
- Boot length: 6"
- Boot Diameter (widest point): 15/16"
| Singles | 4-Cable Set | 6-Cable Set | 8-Cable Set |
|
$39.99
|
$129.99
|
$179.99
|
$219.99
|
Long Boot Plasma Ignition Cables (Stage I)
These plasma cables are suited for engines where the spark plugs are recessed. Instead of having a second conductor coming out of the boot, a threaded nut is exposed on the top of the boot which is used to connect the output from the plasma module.
Long Boot Plasma cable
- Long reach boot for engines with recessed plugs
- High voltage wire from boot is 3ft in length
- High voltage conductor is 8mm spark plug wire
- Plasma current delivery through screw connect
- Internal Protection of 40kV
- Boot length: 6"
- Boot Diameter (widest point): 15/16"
- Long reach boot for engines with recessed plugs
- High voltage wire from boot is 3ft in length
- High voltage conductor is 8mm spark plug wire
- Plasma current delivery through screw connect
- Internal Protection of 40kV
- Boot length: 6"
- Boot Diameter (widest point): 15/16"
| Singles | 4-Cable Set | 6-Cable Set | 8-Cable Set |
|
$39.99
|
$129.99
|
$179.99
|
$219.99
|
Ford Plasma Coil on Plug
These state of the art coil on plugs are a true plug and play solution. Simply replace the existing COPs with the plasma COPs, hook up the factory harness to the respective coils, connect the plasma outputs to the COP plasma terminals and you're done. These are first in the long line of plasma COPs to come
Long Boot Plasma cable
- Long reach boot for engines with recessed plugs
- High voltage wire from boot is 3ft in length
- High voltage conductor is 8mm spark plug wire
- Plasma current delivery through screw connect
- Internal Protection of 40kV
- Boot length: 6"
- Boot Diameter (widest point): 15/16"
- Long reach boot for engines with recessed plugs
- High voltage wire from boot is 3ft in length
- High voltage conductor is 8mm spark plug wire
- Plasma current delivery through screw connect
- Internal Protection of 40kV
- Boot length: 6"
- Boot Diameter (widest point): 15/16"
| Singles | 4-Coil Set | 6-Coil Set | 8-Coil Set |
|
$59.99
|
$219.99
|
$309.99
|
$369.99
|
Plasma Distribution Bricks (Stage II)
Plasma Distribution Brick Specification
- 4-Channel Plasma Distributor (4 Cylinder)
- Combines High-voltage signal from coil / distributor with the high current plasma signal
- Standard Sparkplug type connect towers
- Internal Protection of 60kV
- Dimensions (L x W): 7.75" x 2"
$199.99
- 4-Channel Plasma Distributor (4 Cylinder)
- Combines High-voltage signal from coil / distributor with the high current plasma signal
- Standard Sparkplug type connect towers
- Internal Protection of 60kV
- Dimensions (L x W): 7.75" x 2"
Purchase and Warranty terms
The product is guaranteed to be free from manufacturing defects for a period of 90 days after purchase. The warranty does not cover units damaged as a result of incorrect wiring / installation by the buyer and failure to follow proper installation instructions. The buyer assumes all responsibility and liability for proper and safe handling of goods. Furthermore, the user indemnifies www.aquapulser.com from all claims arising from the handling or use of the goods. It is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge and high voltage generated by the ignition coil and the sparkamp module. By purchasing the unit, the buyer agrees that the sole and exclusive maximum liability to www.aquapulser.com arising from any product sold on the website shall be the price of the product ordered. In no event shall www.aquapulser.com, its directors, officers, employees or other representatives be liable for special, indirect, consequential, or punitive damages related to the products sold. NO PARTY SHALL BE LIABLE TO ANY OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
